Page 342 - byob-catalog

340
HOSE & CLAMPS
Water/Heater Hose
Series 130
Low Permeation Marine Fuel Hose
Series 368 Type A
mfr
SHI
mfr
SHI
This Water/Heater Hose is fabric-reinforced and has an EPDM tube and cover. This hose is primarily used for engine heater hose, heat exchanger, A/C circulation, and drain lines (sink, icebox, shower and livewell). It is resistant to mild chemicals, heat, cold, ozone and saltwater.
Low permeation marine fuel hose has a plastic barrier veneer with an outer layer tube to limit permeation. This polyester reinforced hose complies with EPA and CARB very low permeation requirements and is weather/UV resistant. This hose is primarily used for fuel feed (gasoline up to 85% ethanol blended fuels/diesel/all bio-diesel blends). It meets USCG Type A1 - 15 requirements for pleasure boats and meets SAE J1527 Type A1-15, ISO 7840 Type A1, and NMMA/CE type accepted standards. The temperature ranges from -20F to 212F.
Size Part No.
1/2" 16-130-0126
5/8" 16-130-0586
3/4" 16-130-0346
Water/Heater Hose
Per Foot
$1.94
$2.14
Working PSI
62
62
50
2.80
50' Box Per 50' Box
16-368-0146 $156.65
16-368-0566 $164.44
116-368-0386 $168.96
Size Part No. Per Foot
1/4" 16-368-0140 $2.71
5/16" 16-368-0560 $2.90
3/8" 16-368-0380 $3.00
1/2" 16-368-0120 $3.86
Silverado 4000 Fuel Line
mfr
SHI
Series 337
Series 160
116-368-0126 $223.25
Water/Heater Hose has a good bend radius, is fabric reinforced, and has an EPDM tube and cover. This hose is primarily used for critical water connections, heat exchanger, toilet intake, small engine intake, bilge pump intake/discharge, and below water line drains and scup- pers. It is resistant to mild chemicals, heat, cold, ozone and saltwater. Working PSI: 250
Size Part No. Per Foot
1/2" 16-160-0126B $3.27
mfr
SHI
5/8"
3/4"
1"
mfr
SHI
16-160-0586B
16-160-0346B
16-160-1006B
$3.08
$3.64
$4.60
Silverado 4000 fuel line is constructed with a non-permeable THV barrier layer, polyester reinforcement, and a CPE weather and UV resistant cover. It meets all current EPA and CARB standards. The hose construction is easier to rig, clamp and maintains its flexibility under a range of extreme environmental conditions.
Size Part No.
3/8" 116-337-0380
5/16" 116-337-0560
Fire-Alcohol Fuel Fill Hose
Per Foot 50' Carton
$2.74 116-337-0386
Per Carton
$162.00
$156.42
$2.57 116-337-0566
90° Rubber Elbow EPDM
Series 290
Shields 90° rubber elbows are made of 100% high temperature EPDM rubber and have a maximum operating temperature of 250°F (121°C).
Series 350 Type A
Size Part No.
2" 116-290-2000-1
2-1/2" 116-290-2120-1
3" 116-290-3000-1
3-1/2" 116-290-3120-1
4" 116-290-4000-1
5" 116-290-5000-1
6" 116-290-6000-1
8" 116-290-8000-1
Hump Hose Connector EPDM
Series 220
Shields hump hose connectors are made of 100% high temperature EPDM rubber and have a max- imum operating temperature of 250°F (121°C).
Each
$28.31
$32.27
$33.30
$39.34
$46.07
$58.64
$70.92
Shields Fire-Acol Fuel Fill Series 350 offers a solution to this issue. Fire-Acol uses a buna-n-vinyl cover that is very resistant to ethanol fuel. The hose will withstand exposure to fuel stored in the hose after refueling.
mfr
SHI
Size Part No.
1-7/8" 16-350-1780
2" 16-350-2000
2-3/8" 16-350-2380
Fuel Fill Hose
Per Foot
$18.61
$20.16
$182.56
$23.40
mfr
SHI
Series 355 Type A
Size Part No.
3" 116-220-3000-1
3-1/2" 116-220-3120-1
4" 116-220-4000-1
5" 116-220-5000-1
6" 116-220-6000-1
8" 116-220-8000-1
Each
$30.20
$38.64
$39.17
$42.60
$47.45
$121.70
Shields Fire-Acol – Fuel Fill Hose resists gasoline/alcohol blends and is compounded for low permeation. It is abrasion resistant and it is reinforced with wire helix embedded between piles of HD synthetic cord. This imported hose is primarily used for fuel fill (gas or diesel) and is for pleasure boats only.
Size Part No. Per Foot
1-1/2" 16-355-1120 $11.25
mfr
SHI
We cut most hose to custom lengths in Per Foot increments. Cost savings on boxes if available.
Please contact us for clamp sizes. 1-800-327-3792
EXHAUST/WATER & FUEL HOSE