Page 180 - byob-catalog

178
ELECTRICAL
mfr
BSS
Ø1.95" DIA. 49.53mm Stainless Steel Cap Diameter
Ø1.70" DIA. 43.18mm Plastic Ring Diameter
1001
DECK RING
Ø2.27" DIA 57.66mm Stainless Steel Cap Diameter
Ø2.17" DIA 55.02mm Plastic Ring Diameter
1002
cables need to be extended.
• Includes one black and one red insulating boot. Specifications:
Continuous Rating:
Cable Clams
Dual PowerPost Cable Connectors
COMPRESSION RING
mfr
BSS
GASKET SEAL
CABLE
Ø2.76" DIA 70.10mm Stainless Steel Cap Diameter
Ø2.67" DIA 67.70mm Plastic Ring Diameter
1003
Provides a waterproof pass-through for antenna cables without re- quiring removal of the factory installed connector. Features: Save the expense of removing and replacing connectors. Avoid poor connections from removing factory connectors. Use 1001 for GPS cables, 1002 for VHF cables and 1003 for radar cables. Pre-drilled and slit rubber seals for easier installation. Stainless steel fasteners included. Specifications: Ring Material UV-Stabilized Thermoplastic, Seal Material UV-Stabilized Buna-N Rubber, Stainless Steel Cap.
• 2016/2017 are designed for connecting high amperage conductors. • 2018 is designed for outboard engine installation when factory
Mounting hole for #6 Screw
Ø0.68" DIA 17.27mm
0.65" TYP. 16.51mm
1001
Mounting hole for #8 Screw
Ø0.834" DIA 21.18mm
0.775" TYP. 19.69mm
Mounting hole for #8 Screw
Ø1.396" DIA 35.46mm
1.018" TYP. 25.86mm
Maximum Voltage Rating: Mounting Holes:
Not rated—amperage flows between terminals stacked on post and is deter mined by wire and terminals used.
48 Volts DC
Accepts #10 (M5) Screws
Part No.
2016 2017
mfr
BSS
Each
Terminal Studs
Weight Lb (Kg)
0.27 (0.12) 0.27 (0.12)
$24.49 2x5/16" $24.49 2x3/8"
600-Amp Power Bar
Tin-Plated
Part No.
1001 1002 1003
mfr
BSS
Each
$24.19 $24.74 $27.49
Max. Connector Dia. in (mm) 0.68 (17.0) 0.83 (21.0) 1.40 (35.0)
Max. Cable Dia. in (mm) 0.31 (8.0) 0.44 (11.0) 0.56 (14.0)
Mounting Holes
#6 x 7/8" screws
#8 x 7/8" screws #8 x 7/8" screws
A negative consolidation terminal with a single cable connection to the engine ground. Made from DCA110 copper with 3/8" studs. It allows terminals to be attached without clearance problems. Additional 8-32 terminals provide attachment points for smaller circuits.
Part No.
Each Amps
$122.99 600
$26.49 Insulated Cover for 2104
Terminals
4
2127
DualBus Plus Busbar
130 Amps AC/150 Amp DC
2104 2708
mfr
BSS
250-Amp MaxiBus Busbars
2105
Tin-Plated
Combines negative and positive buses on one block. The clear poly- carbonate cover snaps on to meet Coast Guard and ABYC insulation requirements. Tin-plated copper bus and glass-reinforced lexan base. Continuous Amps: 130 AC, 150 DC, max. Volts: 300 AC, 48 DC.
Glass-reinforced lexan base, tin-plated copper bus and abs cover. Continous Amps. 250 AC/DC, 300 VAC max., 48 VDC max.
Part No.
2722
Each
$32.49
Description
1/4" Stud, 5 x 10-32 Screw Terminals
Part No.
2105 2127
Each Description
$83.99 12 - No. 10 - 32 Screw Terminals $57.49 4 - 5/16" Stud
2304
Tin-Plated MiniBus, BusBar and DualBus Bars
2305 2713, 2709 2302 2715
2702
mfr
BSS
The MiniBus and the BusBar are used to consolidate multiple negative wires or to create a positive bus for feeding multiple circuits. DualBus provides two isolated busses to provide both positive and negative circuits on the same block.
TERMINAL BLOCKS, BUSBARS, CIRCUIT BREAKERS PLUGS & RECEPTACLES, FUSE BLOCKS, FUSES
Part No.
2304 2305 2713
MINIBUS 100 AMPS
Each Description
$19.49 5 Screw, 2 Stud Terminals $21.49 4 Stud Terminals
$3.89 Cover for Both
Part No.
2301 2302 2303 2715
BUSBAR 150 AMPS
Each Description
$25.49 10 Screw, 2 Stud Terminals $39.99 20 Screw, 2 Stud Terminals $33.49 4 Stud Terminals
$4.49 Cover for 2301/2303
Part No.
2701 2702 2709
DUALBUS 100 AMPS
Each Description
$24.99 5+ / 5- Screw Terminals $32.49 10+ / 10- Screw Terminals $14.49 Cover for 2701